Think and Do The Extraordinary
The Campaign for NC State
Think and Do The Extraordinary
The Campaign for NC State

August 15, 2017 | Staff

North Carolina State University engineers have utilized vacuum to create a more efficient, hands-free method for filling complex microchannels with liquid metal. Their work addresses two of the most common difficulties in creating liquid metal-filled microchannels and may enable broader use of liquid metals in electronic and microfluidic applications.

Liquid metals are promising as soft, stretchable electrical components such as antennas, circuits, electrodes and wires. These applications often require the ability to pattern the liquid metal into different and sometimes complicated shapes at scales smaller than 100 microns, or the width of a human hair. This is accomplished by pushing the liquid metal into microchannels – small, hollow, tube-like structures within a flexible elastomer material. The most common method for creating these patterns is injection, which pushes the metal into the channels via a small hole, or inlet.

However, injection has two specific drawbacks. First, the pressure required to push the metal into the microchannel can cause the channels to rupture and leak. Second, to completely fill the channel, the air trapped within it must have a means of escape. That means each channel has to have two openings – an inlet and an outlet – which take up additional space and can cause microchannel deformation at the outlet site.

“Utilizing vacuum allows us to solve both of these problems,” says Michael Dickey, professor of chemical and biomolecular engineering at NC State and corresponding author of a paper describing the work. “We place a drop of liquid metal on top of the inlet and expose the elastomer to vacuum. The air escapes the microchannel through the drop of liquid metal covering the inlet, or through the walls of the channels themselves. When the elastomer is exposed to atmosphere again, the metal gets pushed into the microchannels.”

To test the efficacy of the approach, Dickey and his team created a “maze” of microchannels within poly(dimethylsiloxane), or PDMS, a silicon elastomer commonly used in microfluidic applications. The microchannels were 100 microns wide and 50 microns tall, with small cross-sections, numerous branches, and many dead ends. The small scale and limited space meant there was only one inlet and no room to punch outlets for the air to escape. Then they placed a drop of the liquid metal EGain, a mixture of gallium and indium, on top of the inlet and exposed it to vacuum.

“Using vacuum we found that that the channels completely filled with fewer defects compared to the injection method, and without the need for any outlets,” says Dickey.

A video demonstrating the vacuum fill process can be found here. The paper, “Vacuum Filling of Complex Microchannels with Liquid Metal,” appears in Lab on a Chip. The research was funded by the National Science Foundation (grant DMR-1121107). Graduate students Yiliang Lin and Rashed Khan, undergraduate students Olivia Gordon and Neyanel Vasquez, and Jan Genzer, N. Frank and Susan Culberson Distinguished Professor of Chemical and Biomolecular Engineering at NC State, contributed to the work.

-peake-

Note to editors: An abstract of the paper follows

“Vacuum Filling of Complex Microchannels with Liquid Metal”

Authors: Yiliang Lin, Olivia Gordon, Rashed Khan, Neyanel Vasquez, Jan Genzer, Michael Dickey, North Carolina State University
Published: Aug. 15, 2017 in Lab on a Chip

DOI: 10.1039/C7LC00426E

Abstract:
This paper describes the utilization of vacuum to fill complex microchannels with liquid metal. Microchannels filled with liquid metal are useful as conductors for soft and stretchable electronics, as well as for microfluidic components such as electrodes, antennas, pumps, or heaters. Liquid metals are often injected manually into the inlet of a microchannel using a syringe. Injection can only occur if displaced air in the channels has a pathway to escape, which is usually accomplished using outlets. The positive pressure (relative to atmosphere) needed to inject fluids can also cause leaks or delamination of the channels during injection. Here we show a simple and hands-free method to fill microchannels with liquid metal that addresses these issues. The process begins by covering a single inlet with liquid metal. Placing the entire structure in a vacuum chamber removes the air from the channels and the surrounding elastomer. Restoring atmospheric pressure in the chamber creates a positive pressure differential that pushes the metal into the channels. Experiments and a simple model of the filling process both suggest that the elastomeric channel walls absorb residual air displaced by the metal as it fills the channels. Thus, the metal can fill dead-ends with features as small as several microns and branched structures within seconds without the need for any outlets. The method can also fill completely serpentine microchannels up to a few meters in length. The ability to fill dense and complex geometries with liquid metal in this manner may enable broader application of liquid metals in electronic and microfluidic applications.

This post was originally published in NC State News.

Comments are closed.

«
»